String Chip Cylinder Mould for Paper Machine

• After-sales Service: Online Service
• Warranty: 1 Year
• Certification: ISO 9001:2000, ISO 9001:2008, CE
• Surface Treatment: Acid Pickling
• Manufacturing Process: Forging
• Material: Stainless Steel
• Model NO.: DD380-1100
• Guarantee: 1 Year
• Hardness: >HRC45
• Raw Material: Stainless Steel
• Application: Paper Making Industry
• Name: Paper Machine Cylinder Mould
• Condition: New
• Design Speed: Low Speed
• Size: Customization
• Shipping Port: Customization
• Brand: Customization
• Package: Standard
• Freight Charge: According Actual
• Paper Kind: Toilet,Napkin,Fical Paper etc
• Pre-Sales Service: 24 Hours Online Support,Help to Design
• After Sales Service: Video Guidance, Field Guidance
• Transport Package: Standard Sea Shipment Package
• Specification: According to customized
• Trademark: LEI ZHAN
• Origin: China
• HS Code: 84399900
• Production Capacity: 50000 Set/Year

Product Description

Paper Machine Cylinder Mould Introduce:

Cylinder is the main part in cylinder paper machine on which the paper width is formed.It is required to filter water evenly and not produce too much stirring in the trough when rotating.The cage should have sufficient stiffness and accurate geometry and should be installed horizontally.


The rotary shaft is fitted with a brass support bar device called spokes, with spokes spaced 100-150mm apart.The spokes support the central rim of the wheel, which is surrounded by grooves with horizontal bars of the same length as the net cage.The horizontal strip is about 1cm in diameter and 4cm from the center, parallel to the central axis.The bar is made of steel or brass and the section may be round or rectangular.There are protruding wheel rings on the outermost wheel rings, which are used to seal the corresponding parts of the net groove, so as to isolate the inside and outside of the cylinder.In the horizontal bar according to the spiral milling out of serrated groove, with a continuous diameter of about 3mm of metal wire spiral wound in the cylinder, then form a cage cylinder frame.The gap between adjacent wires is about 1cm.Finally, the copper wire is first covered with a thick brass or stainless steel inner mesh, and then covered with a thin surface mesh for paper making.In the net and face net are terminal net, is a special tool to tighten in the cylinder frame, with silver welding or welding butt up.The final assembly must concentric with the central shaft, and its stiffness should be sufficient to withstand the pressure of the volute roll without deformation.
 

The cylinder bearing device is outside the net groove.The two ends of the cylinder are connected with the side box of the net slot.Slurry after the Internet, through the copper mesh filter into the cylinder of white water, from both ends of the cylinder into the side box, and then out of the white water pump circulation.

 

Product Description

Paper Machine Cylinder Mould is used in the forming section of paper making machines and thickener, our Cylinder Mould features in high speed, high strength, low power consumption, long life time for wire. LEIZHAN employ proprietary manufacturing techniques, sound engineering principles and a team effort to develop the best cylinder mould for your application.

A complete set of Cylinder Mould Former include: cylinder mould, couch roll , guide roll, felt foil box ,movable spray pipe ,frame and base plate .
Foundation part including sole plate, anchor bolt ,nut etc. foundation drawing content : reserve hole position ,size, elevation, the static and dynamic load of each driving point. it is only for technical reference. the sole plate material is cast iron HT200 , through 2 times again eliminate stress processing.

Detailed Photos

 

Product Parameters

Surface construction is very important in designing the right cylinder mould for your specific machine.

Cylinder size, speed, loading, dewatering requirements and open area are some of the variables we consider when recommending a surface construction and face wire selection that will enable your cylinder to operate at maximum efficiency.

Three examples of surface construction, using various sizes and style of top rods and winding wire, illustrate how open area can be altered.Our years of experience in constructing cylinder moulds enable us to recommend the best design for your machine.

Type	Common	Winding	String Chip	Air exhaust	Vacuum
Diameter	1000~5000mm
Width	1000~8000mm
Material	Cast Steel, Stainless Steel, Copper
Winding Type			String Chip Type
Slice being welded on every rod and slice in fall Winding type cylinder mould is widely being used as its high stability and long service life compared to string chip type.			Rod goes through the slice

Company Profile

 

Winding type	String Chip type
Slice being welded on every rod and slice in fall Winding type cylinder mould is widely being used as its high stability and long service life compared to string chip type.	Rod goes through the slice
Photo interpretation	Photo interpretation

Product Show




 

How to make an inquiry ?
Method 1	Provide us cylinder mould drawing.
Method 2	1. Working speed and working pressure
	2. Cylinder mould diameter and face length
	3. Cylinder mould material
	4. Cylinder mould structure
	5. Paper kind and weight (gsm)
Method 3	If you don't clear with above information,you are welcome to contact with us.We will help you to choose the most suitable cylinder mould.